This training course provides theoretical and hands-on practical knowledge...
This training course provides theoretical and hands-on practical knowledge of three-phase pump and motor rewinding, repair, maintenance, and troubleshooting. Students will learn motor components, winding diagrams, coil removal and rewinding techniques, copper wire selection, fault diagnosis, electrical testing, and safe motor installation and operation. The course prepares trainees for careers in motor repair workshops, pump servicing centers, and electrical maintenance, or for starting their own repair business.
বিদ্যুতের মৌলিক ধারণা: ভোল্টেজ, কারেন্ট, রেজিস্ট্যান্স ও পাওয়ার
AC ও DC বিদ্যুতের পার্থক্য
সিঙ্গেল ফেজ ও থ্রি ফেজ সাপ্লাই
ওহমের সূত্র ও পাওয়ার ক্যালকুলেশন
কন্ডাক্টর, ইনসুলেটর ও ইলেক্ট্রোম্যাগনেটিজম
ইলেকট্রিক্যাল টুলস ও মেজারমেন্ট ইন্সট্রুমেন্ট পরিচিতি
PPE, আর্থিং, শর্ট সার্কিট ও বৈদ্যুতিক দুর্ঘটনা প্রতিরোধ
বিদ্যুৎ বিচ্ছিন্নকরণ, লকআউট/ট্যাগআউট (LOTO) এবং নিরাপদ কাজের নিয়ম
থ্রি ফেজ ইন্ডাকশন মোটরের পরিচিতি
স্টেটর, রোটর, শ্যাফট, বেয়ারিং ও মোটর বডি
Squirrel Cage ও Slip Ring মোটরের ধারণা
মোটরের নেমপ্লেট ও রেটিং পড়া
Pole, RPM, Frequency ও Slip
মোটরের টর্ক, লোড ও দক্ষতা
মোটরের স্টার ও ডেল্টা সংযোগ
মোটরের ঘূর্ণনের দিক পরিবর্তন
Direct-On-Line (DOL) ও Star-Delta Starter-এর পরিচিতি
সেন্ট্রিফিউগাল পাম্পের গঠন ও কার্যপদ্ধতি
সাবমার্সিবল পাম্পের গঠন ও কার্যপদ্ধতি
পাম্প ইমপেলার, শ্যাফট, সিল ও বেয়ারিং
মোটর ও পাম্পের কাপলিং এবং অ্যালাইনমেন্ট
পানির প্রবাহ, হেড ও ডিসচার্জের প্রাথমিক ধারণা
পাম্পে পানি না ওঠার কারণ
ড্রাই রানিং, ওভারলোড ও অতিরিক্ত গরম হওয়ার সমস্যা
মাল্টিমিটার ব্যবহার
ক্ল্যাম্প মিটার দিয়ে কারেন্ট পরিমাপ
মেগার দিয়ে ইনসুলেশন রেজিস্ট্যান্স পরীক্ষা
তিন ফেজ উইন্ডিংয়ের Continuity Test
তিন ফেজ উইন্ডিংয়ের Resistance Comparison
Phase-to-Phase ও Winding-to-Earth ইনসুলেশন পরীক্ষা
সাপ্লাই ভোল্টেজ ও ফেজের ভারসাম্য পরীক্ষা
বেয়ারিং, শ্যাফট ও কুলিং ফ্যান পরীক্ষা
বার্ন্ট কয়েল, ওপেন সার্কিট ও শর্ট সার্কিট শনাক্তকরণ
মোটর টেস্টিংয়ের এই বিষয়গুলো ব্যবহারিকভাবে শেখানো উচিত; পরীক্ষার গ্রহণযোগ্য মান মোটরের রেটিং, নির্মাতার নির্দেশনা ও প্রযোজ্য স্ট্যান্ডার্ড অনুযায়ী নির্ধারণ করতে হবে।
মোটর খোলার আগে প্রাথমিক পরীক্ষা
মোটরের ছবি ও কানেকশন রেকর্ড রাখা
টার্মিনাল মার্কিং: U1, V1, W1, U2, V2, W2
বেয়ারিং ও এন্ড কভার খোলা
রোটর ও স্টেটর আলাদা করা
পুরোনো কয়েলের অবস্থা পর্যবেক্ষণ
Slot সংখ্যা, Pole সংখ্যা ও Coil Pitch নির্ণয়
কয়েলের Turns, Wire Gauge ও Connection Data সংগ্রহ
Winding Diagram ও Winding Data Sheet তৈরি
পুরোনো উইন্ডিং অপসারণ এবং স্টেটর স্লট পরিষ্কার করা
রি-ওয়াইন্ডিংয়ের জন্য প্রয়োজনীয় উপকরণ নির্বাচন
এনামেলড কপার ওয়্যার ও তারের গেজ নির্বাচন
স্লট ইনসুলেশন ও ফেজ ইনসুলেশন
কয়েল ফর্মার তৈরি
কয়েল উইন্ডিং মেশিন পরিচালনা
সঠিক Turns ও Coil Pitch অনুযায়ী কয়েল তৈরি
স্টেটর স্লটে কয়েল প্রবেশ করানো
কয়েল গ্রুপিং ও ফেজ বিন্যাস
Single-Layer ও Double-Layer Winding
কয়েলের Start ও Finish চিহ্নিত করা
কয়েল সংযোগ, জয়েন্ট ও ইনসুলেশন
লেসিং, ওয়েজিং ও উইন্ডিং ফিনিশিং
থ্রি ফেজের তিনটি উইন্ডিং শনাক্তকরণ
Series ও Parallel Coil Connection
Star Connection
Delta Connection
Pole ও Coil Group-এর সম্পর্ক
Winding Diagram অনুসরণ করে সংযোগ
কয়েল সংযোগের Continuity ও Resistance পরীক্ষা
ভুল ফেজ সংযোগ ও ভুল Turns-এর সমস্যা
টার্মিনাল বক্সে সঠিক লিড সংযোগ
মোটরের ঘূর্ণনের দিক পরীক্ষা
স্লট লাইনার, ইনসুলেশন পেপার ও ইনসুলেটিং স্লিভ
কয়েল ইনসুলেশন ও ফেজ সেপারেশন
উইন্ডিং লেসিং ও ওয়েজিং
ইনসুলেশন বার্নিশের ব্যবহার
অনুমোদিত পদ্ধতিতে বার্নিশ শুকানো ও কিউরিং
স্টেটর ও রোটর পরীক্ষা
বেয়ারিং পরীক্ষা ও প্রয়োজনে প্রতিস্থাপন
শ্যাফট ও এন্ড কভার পুনরায় স্থাপন
মোটর অ্যাসেম্বলি ও ম্যানুয়াল রোটেশন পরীক্ষা
|
সমস্যা |
সম্ভাব্য কারণ ও পরীক্ষার বিষয় |
|---|---|
|
মোটর চালু হয় না |
সাপ্লাই, ফিউজ, কন্টাক্টর, ওভারলোড ও উইন্ডিং পরীক্ষা |
|
মোটর অতিরিক্ত গরম |
ওভারলোড, ভোল্টেজের ভারসাম্যহীনতা, কুলিং ও উইন্ডিং পরীক্ষা |
|
মোটর শব্দ করে |
বেয়ারিং, অ্যালাইনমেন্ট, রোটর ও মেকানিক্যাল ঘর্ষণ পরীক্ষা |
|
মোটর অতিরিক্ত কারেন্ট নেয় |
লোড, ভোল্টেজ, ফেজ ও উইন্ডিংয়ের অবস্থা পরীক্ষা |
|
মোটর বারবার ট্রিপ করে |
ওভারলোড সেটিং, ফেজ সমস্যা, শর্ট সার্কিট ও লোড পরীক্ষা |
|
মোটর ঘুরলেও পাম্প পানি তোলে না |
প্রাইমিং, ইমপেলার, পাইপলাইন, লিকেজ ও ঘূর্ণনের দিক পরীক্ষা |
|
সাবমার্সিবল পাম্প বন্ধ |
কেবল, ইনসুলেশন, সাপ্লাই, সিল ও পাম্পের অবস্থা পরীক্ষা |
|
রি-ওয়াইন্ডিংয়ের পর মোটর গরম |
Turns, সংযোগ, ইনসুলেশন, ফেজ কারেন্ট ও লোড যাচাই |
একটি থ্রি ফেজ মোটর খুলে যন্ত্রাংশ শনাক্ত করা
পুরোনো উইন্ডিংয়ের ডাটা সংগ্রহ
Winding Diagram ও Data Sheet তৈরি
কয়েল তৈরি ও স্টেটরে বসানো
Star/Delta সংযোগ সম্পন্ন করা
Continuity ও Insulation Resistance Test করা
মোটর পুনরায় অ্যাসেম্বলি করা
নিরাপদ নিয়ন্ত্রিত পরিবেশে No-Load Test
কারেন্ট, শব্দ, কম্পন ও তাপমাত্রা পর্যবেক্ষণ
একটি পাম্পের ত্রুটি নির্ণয় ও মেরামত
কাজের রিপোর্ট ও চূড়ান্ত ব্যবহারিক পরীক্ষা
এই মডিউলগুলোর কাঠামো প্রচলিত মোটর রি-ওয়াইন্ডিং প্রশিক্ষণ এবং দক্ষতাভিত্তিক ট্রেনিং নির্দেশিকার সঙ্গে সামঞ্জস্য রেখে সাজানো হয়েছে।
নিচের পরিকল্পনাটি সপ্তাহে ৩ দিন, প্রতিদিন ৩ ঘণ্টা ধরে তৈরি করা হয়েছে। মোট ১২ সপ্তাহে প্রায় ১০৮ ঘণ্টা প্রশিক্ষণ হবে।
|
সপ্তাহ |
প্রশিক্ষণের বিষয় |
ব্যবহারিক কাজ |
|---|---|---|
|
১ |
ইলেকট্রিক্যাল বেসিক ও নিরাপত্তা |
টুলস পরিচিতি, নিরাপত্তা অনুশীলন |
|
২ |
থ্রি ফেজ মোটরের গঠন |
মোটর খোলা ও যন্ত্রাংশ শনাক্ত |
|
৩ |
পাম্পের গঠন ও কার্যপদ্ধতি |
পাম্প খোলা ও যন্ত্রাংশ পরীক্ষা |
|
৪ |
মোটর টেস্টিং |
মাল্টিমিটার, ক্ল্যাম্প মিটার ও মেগার |
|
৫ |
উইন্ডিং ডাটা সংগ্রহ |
Turns, Slot, Pole ও Wire Gauge নথিভুক্ত |
|
৬ |
কয়েল তৈরি |
কয়েল ফর্মার ও উইন্ডিং মেশিন ব্যবহার |
|
৭ |
কয়েল ইনসারশন |
স্টেটরে কয়েল বসানো ও লেসিং |
|
৮ |
উইন্ডিং কানেকশন |
স্টার-ডেল্টা ও টার্মিনাল সংযোগ |
|
৯ |
ইনসুলেশন ও ফিনিশিং |
বার্নিশ, কিউরিং ও মান যাচাই |
|
১০ |
মোটর অ্যাসেম্বলি |
বেয়ারিং, শ্যাফট ও এন্ড কভার স্থাপন |
|
১১ |
ট্রাবলশুটিং |
মোটর ও পাম্পের ত্রুটি নির্ণয় |
|
১২ |
চূড়ান্ত প্রজেক্ট |
রি-ওয়াইন্ডিং, টেস্টিং ও মূল্যায়ন |
প্রশিক্ষণ পরিচালনার পরামর্শ: ১০৮ ঘণ্টার এই কোর্সটি একটি প্রাথমিক প্রশিক্ষণ পরিকল্পনা। বড় মোটরের পূর্ণ রি-ওয়াইন্ডিং এবং একাধিক ধরনের সাবমার্সিবল পাম্পে দক্ষতা অর্জনের জন্য অতিরিক্ত সময় ও বাস্তব কাজের অনুশীলন লাগতে পারে।
টেস্টিং ইন্সট্রুমেন্ট
ডিজিটাল মাল্টিমিটার
ক্ল্যাম্প মিটার
ইনসুলেশন রেজিস্ট্যান্স টেস্টার বা মেগার
ট্যাকোমিটার ও থার্মোমিটার
উপযুক্ত সুরক্ষাসহ মোটর টেস্টিং প্যানেল
রি-ওয়াইন্ডিং যন্ত্রপাতি
কয়েল উইন্ডিং মেশিন ও ফর্মার
এনামেলড কপার ওয়্যার
ইনসুলেশন পেপার ও স্লিভ
ওয়েজ, লেসিং কর্ড ও বার্নিশ
কাটার, প্লায়ার্স, স্ক্রু ড্রাইভার ও স্প্যানার
প্র্যাকটিক্যাল মডেল
বিভিন্ন রেটিংয়ের থ্রি ফেজ মোটর
সাবমার্সিবল পাম্প ও সাধারণ পানির পাম্প
ত্রুটিযুক্ত মোটর ও পাম্প
স্টার-ডেল্টা স্টার্টার ও কন্ট্রোল প্যানেল
বেয়ারিং, সিল, ইমপেলার ও শ্যাফট
|
মূল্যায়ন |
নম্বর |
|---|---|
|
থিওরি পরীক্ষা |
২০ |
|
ব্যবহারিক কাজ |
৪০ |
|
ত্রুটি নির্ণয় |
২০ |
|
নিরাপত্তা ও কাজের রিপোর্ট |
১০ |
|
উপস্থিতি ও শৃঙ্খলা |
১০ |
|
মোট |
১০০ |
প্রস্তাবিত পাস নম্বর ৬০। তবে ব্যবহারিক নিরাপত্তার গুরুত্বপূর্ণ শর্তগুলো আলাদাভাবে পূরণ করতে হবে।
থ্রি ফেজ মোটর ও পাম্পের প্রধান যন্ত্রাংশ শনাক্ত করতে পারবে।
মোটর খুলে উইন্ডিং ডাটা সংগ্রহ করতে পারবে।
নির্দেশনা অনুযায়ী কয়েল তৈরি ও রি-ওয়াইন্ডিং করতে পারবে।
স্টার-ডেল্টা সংযোগ ও মৌলিক মোটর টেস্টিং করতে পারবে।
মোটর ও পাম্পের সাধারণ বৈদ্যুতিক ও মেকানিক্যাল ত্রুটি নির্ণয় করতে পারবে।
নিরাপদ পদ্ধতিতে মোটর মেরামত, অ্যাসেম্বলি ও রক্ষণাবেক্ষণ করতে পারবে।
গুরুত্বপূর্ণ নিরাপত্তা শর্ত: প্রশিক্ষণের সময় বিদ্যুৎ বিচ্ছিন্ন ও নিশ্চিতভাবে নিরাপদ করা ছাড়া মোটর খোলা বা উইন্ডিংয়ে কাজ করা যাবে না। লাইভ টেস্ট কেবল প্রশিক্ষকের তত্ত্বাবধানে, সুরক্ষিত টেস্টিং সেটআপে করতে হবে। উচ্চ ভোল্টেজের মোটর রি-ওয়াইন্ডিং এই প্রাথমিক কোর্সের আওতাভুক্ত নয়।
Basic concepts of voltage, current, resistance, and electrical power
AC and DC electricity
Single-phase and three-phase power supply
Ohm's Law and power calculations
Conductors, insulators, and electromagnetism
Introduction to electrical tools and measuring instruments
Electrical hazards, short circuits, and accident prevention
Personal Protective Equipment (PPE)
Earthing, isolation, and Lockout/Tagout (LOTO) procedures
Introduction to three-phase induction motors
Motor construction and operating principles
Stator, rotor, shaft, bearings, and motor housing
Squirrel cage and slip-ring motors
Reading motor nameplates and ratings
Poles, RPM, frequency, and slip
Motor torque, load, and efficiency
Star and Delta connections
Reversing motor rotation
Introduction to Direct-On-Line (DOL) and Star-Delta starters
Centrifugal pump construction and operation
Submersible pump construction and operation
Impellers, shafts, seals, and bearings
Motor-pump coupling and alignment
Basic concepts of flow rate, head, and discharge
Causes of pump failure and low water delivery
Dry running, overloading, and overheating
Pump maintenance and inspection
Using a digital multimeter
Measuring current with a clamp meter
Insulation resistance testing with a megohmmeter
Continuity testing of three-phase windings
Comparing winding resistance between phases
Phase-to-phase and winding-to-earth insulation testing
Supply voltage and phase imbalance testing
Bearing, shaft, and cooling fan inspection
Identifying open circuits, short circuits, and burnt windings
Preliminary motor inspection before dismantling
Recording motor condition and terminal connections
Identifying U1, V1, W1, U2, V2, and W2 terminals
Removing end covers and bearings
Separating the rotor and stator
Inspecting old windings
Identifying slot numbers, pole numbers, and coil pitch
Recording coil turns, wire gauge, and winding connections
Preparing winding diagrams and data sheets
Removing old windings and cleaning stator slots
Selecting materials for motor rewinding
Enamelled copper wire and wire gauge selection
Slot insulation and phase insulation
Preparing coil formers
Operating a coil winding machine
Winding coils according to the required turns and coil pitch
Inserting coils into stator slots
Coil grouping and phase arrangement
Single-layer and double-layer winding
Identifying coil start and finish leads
Coil connections, joints, and insulation
Lacing, wedging, and winding finishing
Identifying the three motor phases
Series and parallel coil connections
Star connection
Delta connection
Relationship between poles and coil groups
Following winding diagrams
Continuity and resistance testing of coil connections
Identifying incorrect connections and winding turns
Terminal box wiring
Checking motor direction of rotation
Slot liners, insulation paper, and insulating sleeves
Coil insulation and phase separation
Winding lacing and wedging
Application of electrical insulating varnish
Approved varnish drying and curing procedures
Stator and rotor inspection
Bearing inspection and replacement
Shaft and end-cover installation
Motor reassembly
Manual shaft rotation and mechanical inspection
|
Problem |
Possible Causes and Diagnostic Checks |
|---|---|
|
Motor does not start |
Check power supply, fuses, contactor, overload protection, and windings |
|
Motor overheats |
Check overload, voltage imbalance, cooling, and winding condition |
|
Motor makes unusual noise |
Inspect bearings, alignment, rotor, and mechanical friction |
|
Motor draws excessive current |
Check load, voltage, phase balance, and winding condition |
|
Motor trips repeatedly |
Inspect overload settings, phase faults, short circuits, and load |
|
Pump runs but delivers no water |
Check priming, impeller, pipeline, leakage, and rotation direction |
|
Submersible pump stops working |
Check cable, insulation, power supply, seals, and pump condition |
|
Motor overheats after rewinding |
Verify winding turns, connections, insulation, phase current, and load |
Dismantling a three-phase motor and identifying its components
Collecting original winding data
Preparing a winding diagram and data sheet
Making coils and inserting them into stator slots
Completing Star/Delta connections
Performing continuity and insulation resistance tests
Reassembling the motor
Conducting a supervised, controlled no-load test
Monitoring current, noise, vibration, and temperature
Diagnosing and repairing a pump fault
Preparing a maintenance and repair report
Completing the final practical examination
Suggested schedule: 3 days per week, 3 hours per day — approximately 108 training hours.
|
Week |
Training Topics |
Practical Activities |
|---|---|---|
|
1 |
Electrical fundamentals and safety |
Tool identification and safety procedures |
|
2 |
Motor construction |
Motor dismantling and component identification |
|
3 |
Pump construction |
Pump dismantling and inspection |
|
4 |
Motor testing |
Multimeter, clamp meter, and megohmmeter |
|
5 |
Winding data collection |
Recording turns, slots, poles, and wire gauge |
|
6 |
Coil manufacturing |
Coil former and winding machine operation |
|
7 |
Coil insertion |
Stator winding insertion and lacing |
|
8 |
Winding connections |
Star/Delta and terminal connections |
|
9 |
Insulation and finishing |
Varnishing, curing, and quality checks |
|
10 |
Motor assembly |
Bearings, shaft, and end-cover installation |
|
11 |
Troubleshooting |
Motor and pump fault diagnosis |
|
12 |
Final project |
Rewinding, testing, and assessment |
1. Testing Instruments
Digital multimeter
Clamp meter
Insulation resistance tester (megohmmeter)
Tachometer and thermometer
Protected motor testing panel
2. Rewinding Tools and Materials
Coil winding machine and formers
Enamelled copper wire
Insulation paper and sleeves
Slot wedges and lacing cord
Insulating varnish
Pliers, cutters, screwdrivers, and spanners
3. Practical Training Equipment
Three-phase electric motors of different ratings
Submersible pumps and centrifugal pumps
Faulty motors and pumps for practice
Star-Delta starters and control panels
Bearings, seals, impellers, and shafts
|
Assessment Category |
Marks |
|---|---|
|
Theoretical Examination |
20 |
|
Practical Work |
40 |
|
Fault Diagnosis |
20 |
|
Safety and Work Reports |
10 |
|
Attendance and Discipline |
10 |
|
Total |
100 |
Suggested passing mark: 60 out of 100, subject to satisfactory performance in essential safety procedures.
After completing the course, trainees should be able to:
Identify the main components of three-phase motors and pumps.
Dismantle motors and record winding data.
Manufacture coils and perform rewinding under appropriate supervision.
Perform Star/Delta connections and basic motor testing.
Diagnose common electrical and mechanical faults in motors and pumps.
Perform motor assembly, maintenance, and basic repairs safely.
Prepare basic inspection, testing, and repair reports.
Always isolate the power supply and verify that equipment is de-energized before dismantling or rewinding.
Conduct live testing only under qualified supervision using suitable protective equipment and a properly protected test setup.
Follow manufacturer specifications for insulation testing, winding data, and acceptance limits.
Advanced high-voltage motor rewinding is outside the scope of this introductory course.
Real feedback from graduates working in top companies and freelancing worldwide.
This SEO course completely changed my career. Within 3 months of finishing, I got my first international client. The live projects gave me real confidence.
Best investment I made in my career. The instructor's hands-on approach and real-world examples made complex topics super easy to understand.
I ranked my own e-commerce site on Google's first page after this course. The technical SEO module alone was worth the entire fee.